Well, the board is either fixed, or it's going to run terribly. Cross your fingers and hope for the best. I'm at my technical limit right now.

Please help me I.D these stripper clips.

Post Reply
Message
Author
User avatar
Rapidrob
Global Moderator
Global Moderator
Posts: 862
Joined: Sat Jun 03, 2017 9:10 am
Age: 68
Location: New Mexico
United States of America

Please help me I.D these stripper clips.

#1 Post by Rapidrob » Fri Dec 21, 2018 5:55 pm

I was going through my stash of stripper clips and chargers and found a few I do not remember and can I.D.
Take a look and see if you can help out with what they were used for,what country and the caliber them held.
Thanks for any help.
CLICK ON IMAGE FOR MUCH LARGER VIEW
Clips are Aluminum and may be 7.5 French?
clipA.jpg
*********************************************
BXN 52 7.62x25 or 9mm?
clipB.jpg
**********************************************
14 0 51 same as above?
clipC.jpg
clipC2.jpg
*************************************************
This is a neat clip,very well made of brass. Wider than a Springfield clip and marked .35 CAL
clipD.jpg
clipD2.jpg
*************************************************
ZV 91 with two pressed edge tabs
clipE.jpg
clipE2.jpg
***************************************************
"diamond" 50 two pressed edge tabs
clipF.jpg
clipF2.jpg
***************************************************
FMMAP B No edge tabs
clipG.jpg
**************************************************
A very wide,for a rimmed cartridge, stripper looks to be bronze, perhaps 8mm Siamese? ANSWERED
It is a Siamese Mauser stripper clip.
clipH.jpg
clipH1.jpg
****************************************************
Another well made clip marked KB for a rimmed cartridge
clipI.jpg
***************************************************
Tin Can Sailor
'Nam Vet
NRA Endowment Member
President New Mexico Military Surplus Rifle Pistol Shooters

User avatar
Airforce1
Global Moderator
Global Moderator
Posts: 145
Joined: Fri Jun 02, 2017 7:53 pm
Age: 33
Location: Faribault, MN
United States of America

Re: Please help me I.D these stripper clips.

#2 Post by Airforce1 » Fri Dec 21, 2018 8:01 pm

7.5 french on top.
Fmmapb is argy mauser.
.35 one is for the Remington model 8 and 81

User avatar
Ghoulardi
Member
Member
Posts: 275
Joined: Sun Jun 11, 2017 3:06 pm
Age: 63
Location: Cleveland, Ohio
Ukraine

Re: Please help me I.D these stripper clips.

#3 Post by Ghoulardi » Fri Dec 21, 2018 8:16 pm

BXN 52 is for 7.62x25, used to load the CZ 24/26 submachine gun mags. here is the fun part, those also work for 9mm ammo, just like 9mm stripper clips work for 7.62 ammo

carl gustuv 9mm stripper clip
https://www.youtube.com/watch?v=EGS1H8logbA
COOL IT WITH THE BOOM-BOOMS!! OVA-DAY!!

indy1919a4
Gun Nut
Gun Nut
Posts: 962
Joined: Sat Jun 10, 2017 12:23 pm
Age: 56
Location: Indianapolis, Indiana
United States of America

Re: Please help me I.D these stripper clips.

#4 Post by indy1919a4 » Fri Dec 21, 2018 9:08 pm

Wow, I never knew those stripper clips would fit into a block like that..

User avatar
Ghoulardi
Member
Member
Posts: 275
Joined: Sun Jun 11, 2017 3:06 pm
Age: 63
Location: Cleveland, Ohio
Ukraine

Re: Please help me I.D these stripper clips.

#5 Post by Ghoulardi » Fri Dec 21, 2018 11:00 pm

indy1919a4 wrote:
Fri Dec 21, 2018 9:08 pm
Wow, I never knew those stripper clips would fit into a block like that..
that is a arsenal made one piece 'ganged" stripper clip for the carl gustuv 9mm sub-gun mag. it holds 36 rounds ( 5 rows of 6 rounds) which is how many rounds a carl gustuv magazine holds, 36 rounds. it only works with the speed loader made specifically for it. I modified the speed loader to work loading a 7.62x25 PPs43 magazine.

I modified another speed loader to load MP5 magazines

https://www.youtube.com/watch?v=Wc68kbzBufg
COOL IT WITH THE BOOM-BOOMS!! OVA-DAY!!

indy1919a4
Gun Nut
Gun Nut
Posts: 962
Joined: Sat Jun 10, 2017 12:23 pm
Age: 56
Location: Indianapolis, Indiana
United States of America

Re: Please help me I.D these stripper clips.

#6 Post by indy1919a4 » Sat Dec 22, 2018 8:32 am

Now that is neat, never seen a ganged stripper or a stripper like that before.. that looks sharp

User avatar
Ghoulardi
Member
Member
Posts: 275
Joined: Sun Jun 11, 2017 3:06 pm
Age: 63
Location: Cleveland, Ohio
Ukraine

Re: Please help me I.D these stripper clips.

#7 Post by Ghoulardi » Sat Dec 22, 2018 9:56 am

the swedes are pretty clever
COOL IT WITH THE BOOM-BOOMS!! OVA-DAY!!

User avatar
Rapidrob
Global Moderator
Global Moderator
Posts: 862
Joined: Sat Jun 03, 2017 9:10 am
Age: 68
Location: New Mexico
United States of America

Re: Please help me I.D these stripper clips.

#8 Post by Rapidrob » Sun Dec 23, 2018 9:36 am

Anyone have any idea what the last photo clip may be?
Tin Can Sailor
'Nam Vet
NRA Endowment Member
President New Mexico Military Surplus Rifle Pistol Shooters

User avatar
Zeliard
Member
Member
Posts: 250
Joined: Sat Jun 03, 2017 10:27 pm
Age: 40
Location: Southeast US
United States of America

Re: Please help me I.D these stripper clips.

#9 Post by Zeliard » Sun Mar 31, 2019 9:34 pm

Rob,

That last clip is for a 6.5 Mannlicher Schonaeur:

https://www.ebay.ie/itm/Genuine-Vintage ... 3065477751

KB indicates it was made by Kynoch.
Proud alumni of Transylvanian Polygnostic University. "Know enough to be afraid."

"Vertroue in God en die Mauser".-Faith in God and the Mauser.

"Send lawyers, guns and money." -Warren Zevon

Post Reply

Return to “General Firearms Topics”

Who is online

Users browsing this forum: No registered users and 3 guests